Refrigerator Repair in Belvedere Park means a technician at your door with a multimeter, manifold gauge set, and leak detector, not a phone diagnosis. We work the 30032 ZIP, the Memorial Drive corridor, and the Columbia Drive area every week, on Samsung, LG, Whirlpool, GE, and Frigidaire units in ranch and two-story homes. You get a straight answer on what failed and what it costs to fix.
Serving Belvedere Park and nearby
Refrigerator Repair in Belvedere Park is the work of getting a cold box cold again in a neighborhood where the housing stock runs from 1950s ranches to two-story rebuilds, and where the Memorial Drive corridor keeps a lot of kitchens busy. We run calls through 30032, the Columbia Drive area, the Midway Road neighborhood, and the South Decatur side, and we carry the parts that fail most on the brands this area owns: Samsung, LG, Whirlpool, GE, Frigidaire, Maytag, KitchenAid, Sub-Zero, Bosch, and Kenmore. Most calls are a compressor, a control board, a defrost heater, or a door gasket. We test with a multimeter, check the sealed system with a manifold gauge set, and pull a vacuum with a vacuum pump before we charge anything back up. If refrigerant R-134a or R-600a is low, we find the leak with a leak detector instead of topping it off and hoping. Every technician on this route holds EPA Section 608 Certification, and we work to NATE Certification standards on the electrical side. Belvedere Park Refrigerator Repair is not a sideline for us. It is the route.
Belvedere Park sits close to I-285 and major roads, which means we can get a truck to the Midway Road neighborhood or the Columbia Drive area fast, and still make it back across the Memorial Drive corridor the same morning. The neighborhood is established, community-oriented, and full of local referrals, so one good repair on a street usually turns into two more calls on the same block. Older homes here often have kitchens that were updated around a fridge that is now 12 to 18 years old, and those units fail in predictable ways. We serve this area because the demand is steady and the referrals are real.
Belvedere Park Refrigerator Repair calls come in two flavors: a fridge that stopped cooling overnight, and a fridge that has been limping for weeks. We handle both, plus freezer, ice maker, water line, and commercial work. If you are searching for Refrigerator Repair near me Belvedere Park GA at 7 a.m. with a warm fridge, we can usually get a truck to 30032 the same day. Below is what we actually do on this route.
Refrigerator RepairStandard fridge repair in Belvedere Park covers not-cooling, not-freezing, leaks, and noise. We test the thermostat, control board, fan motor, and compressor with a multimeter, then check the sealed system with a manifold gauge set. Most ranch and two-story kitchens in 30032 are a two-to-four-hour job once we confirm the failed part.
Freezer RepairFreezer repair in the Columbia Drive area usually means a defrost system failure or a bad evaporator fan. We pull the panel, test the defrost heater and thermostat, and check for ice buildup blocking airflow. If the freezer is cold but the fridge is warm, that is almost always an airflow or defrost problem, not a compressor.
Ice Maker RepairIce maker repair around the Midway Road neighborhood is often a frozen fill tube or a failed water inlet valve. We check the water line tubing, test the valve, and confirm the maker cycles before we leave. Hard water in this part of DeKalb County scales up valves faster than most homeowners expect.
Refrigerator Water Line InstallationWater line installation in Belvedere Park means running new tubing from the supply to the fridge, usually through a cabinet or under a slab-adjacent floor. We use new water line tubing, a fresh saddle or shutoff, and test every joint under pressure. Older homes on the Memorial Drive corridor often still have brittle original lines.
Refrigerator Water Filter ReplacementWater filter replacement is a quick call, but we do it right: correct filter for the model, flush the line, and check for drips at the housing. In 30032 we see a lot of Samsung and LG units where the filter housing o-ring has dried out and started seeping. We replace the filter and the o-ring together.
Refrigerator Door Seal ReplacementDoor seal replacement fixes the fridge that runs constantly and sweats. We check the door gasket with a dollar-bill test and a flashlight, then replace the gasket and adjust the hinge if the door is sagging. In older Belvedere Park kitchens, a bad gasket is one of the cheapest fixes with the biggest energy payoff.
Refrigerator Compressor RepairCompressor repair is the big-ticket call. We confirm failure with a multimeter and a manifold gauge set before recommending anything, because a bad start relay or control board can mimic a dead compressor. If the compressor is gone, we recover refrigerant with a recovery machine, swap the compressor, pull a vacuum, and recharge.
Refrigerator Thermostat RepairThermostat repair in Belvedere Park starts with temperature logging. We place a probe, watch the cycle, and confirm whether the thermostat is reading wrong or the control board is ignoring it. A thermostat that reads 5 to 10 degrees off will freeze your produce and run your compressor into the ground.
Refrigerator Defrost System RepairDefrost system repair is common in this area because of our humidity. We test the defrost heater, defrost thermostat, and timer or board, then clear the drain. If your freezer has a block of ice on the back wall, the defrost system failed weeks ago and the fridge side is next.
Refrigerator Control Board RepairControl board repair on newer Samsung, LG, and Bosch units is a diagnostic job first. Boards fail from power surges, and we see a spike after summer storms roll through DeKalb County. We test inputs and outputs with a multimeter, confirm the board is the fault, then replace and recalibrate.
Refrigerator Fan Motor RepairFan motor repair addresses the buzzing or grinding noise you hear at night. The evaporator fan moves cold air from the freezer to the fridge; when it seizes, the fridge side warms up while the freezer stays cold. We replace the motor and check the blade for ice interference.
Refrigerator Drain Pan RepairDrain pan repair fixes the puddle under the fridge. In Belvedere Park homes with older floors, a cracked or misaligned drain pan can warp baseboards before you notice. We pull the fridge, inspect the pan and drain tube, clear the clog, and set the unit back level.
Refrigerator Leveling and AlignmentLeveling and alignment stops the door from swinging open and the fridge from rocking. We shim and adjust the front legs so the unit tilts slightly back, which helps the doors close on their own. It also cuts vibration noise on wood floors common in older Belvedere Park homes.
Refrigerator Noise Diagnosis and RepairNoise diagnosis is a listening job. We separate normal compressor hum from a failing fan motor, a rattling drain pan, or a compressor that is about to seize. Loud buzzing plus a warm fridge is urgent; a light hum is usually fine. We tell you which one you have.
Refrigerator Leak Detection and RepairLeak detection covers both water and refrigerant. Water leaks trace to the drain line, water line tubing, or a clogged defrost drain. Refrigerant leaks need a leak detector and a pressure test. We find the source before we quote the fix, so you are not paying for a guess.
Refrigerator Not Cooling DiagnosisNot-cooling diagnosis is our most common Belvedere Park call. We check airflow first, then the evaporator fan, then the defrost system, then the sealed system. About half the time it is a fan or defrost issue, not a compressor, which saves the customer hundreds of dollars.
Refrigerator Not Freezing DiagnosisNot-freezing diagnosis focuses on the freezer side. If the fridge is cold but the freezer is soft, we check the damper, the evaporator fan, and the defrost heater. If both sides are warm, we move to the compressor and sealed system. The order matters for cost.
Refrigerator Overheating RepairOverheating repair starts at the condenser coils. Dust, pet hair, and a failing condenser fan make the compressor run hot, and Atlanta summers push that further. We clean the coils with a coil brush and fin comb, test the fan, and confirm the compressor is not drawing high amps.
Refrigerator Electrical Wiring RepairElectrical wiring repair covers chewed wires, burnt connectors, and failed relays. We trace the circuit with a multimeter, replace damaged wiring, and check the outlet and breaker. Rodent damage is real in older Belvedere Park homes, especially in garages and crawlspaces.
Refrigerator Gas Leak RepairGas leak repair means refrigerant, not natural gas. We use a leak detector and a manifold gauge set to find the loss, then repair the joint, pull a vacuum with a vacuum pump, and recharge with R-134a or R-600a. We recover old refrigerant with a recovery machine first.
Refrigerator Door Hinge RepairDoor hinge repair fixes the door that will not stay shut or hangs crooked. A sagging door lets cold air escape and burns out the compressor over time. We replace the hinge, realign the door, and recheck the gasket seal before we leave.
Refrigerator Shelf and Drawer RepairShelf and drawer repair covers cracked crisper drawers, broken shelf supports, and stuck slides. We source the correct part for your model, fit it, and check that the drawer seals. It is a small job, but a broken crisper drawer ruins produce fast.
Refrigerator Light RepairLight repair is usually a socket, a switch, or a wiring issue, not just a bulb. We test the door switch and the socket with a multimeter, then replace what failed. If the light stays on with the door closed, it is adding heat and costing you cold air.
Refrigerator Temperature Control CalibrationTemperature control calibration gets your fridge back to a real 37 degrees. We place a calibrated probe, log the cycle, and adjust or replace the thermostat or board. If your milk is freezing on the top shelf, the control is off by more than you think.Refrigerator Maintenance Tune-UpMaintenance tune-up covers coil cleaning, gasket check, drain clearing, and temperature verification. We use a coil brush and fin comb on the condenser and check the door seal with a flashlight. Once a year keeps a 12-year-old fridge running in this climate.
Refrigerator InstallationInstallation covers delivery setup, door reversal, water line hookup, and leveling. We measure the cabinet opening first, because Belvedere Park kitchens range from wide ranch layouts to tight two-story galley spaces. Then we set the unit, connect the water line, and test the ice maker.Refrigerator Haul Away and DisposalHaul away and disposal means we remove the old unit when we install the new one. We recover the refrigerant properly with a recovery machine before disposal, which is required and often skipped. You do not have to drag a fridge to the curb or pay a separate hauler.
Refrigerator Preventive Maintenance PlanA preventive maintenance plan puts your fridge on a yearly schedule: coil cleaning, gasket inspection, drain clearing, and temperature check. For Belvedere Park homeowners with a 10-year-old Sub-Zero or KitchenAid, this is cheaper than one compressor replacement. We track the visit and remind you.
Commercial Refrigerator RepairCommercial refrigerator repair serves the restaurants and shops along the Memorial Drive corridor and near South DeKalb Mall. We work early mornings before service, carry common parts, and prioritize units holding food. A walk-in down at 6 a.m. is a same-day call for us.
Built-In Refrigerator RepairBuilt-in refrigerator repair covers Sub-Zero, Bosch, and KitchenAid units that are cabinet-paneled and hard to access. We pull panels carefully, protect the cabinetry, and work in tight clearances. These units need a technician who knows the brand, not a generic parts swap.Most Belvedere Park fridge calls start with a warm fridge and a freezer that still works. We test airflow, the evaporator fan, the defrost system, and the thermostat before we touch the sealed system. If refrigerant is involved, we use a leak detector and a manifold gauge set to find the loss.
Freezer problems in this area usually trace to a defrost failure or a bad evaporator fan. We pull the panel, test the defrost heater and thermostat, and check for ice blocking airflow. If the freezer is cold and the fridge is warm, it is almost never the compressor.
Hard water in this part of DeKalb County scales up ice maker valves and freezes fill tubes. We check the water line tubing, test the inlet valve, and confirm the maker completes a full cycle. A frozen fill tube is a quick fix; a failed valve is a same-visit part swap.
Older homes on the Memorial Drive corridor often still have brittle original water lines. We run new water line tubing from the supply to the fridge, fit a fresh shutoff, and test every joint under pressure. We measure the cabinet opening first so the line routes cleanly.
We work ranch and two-story kitchens across 30032, from tight galley layouts to open ranch kitchens. We measure the cabinet opening and protect floors before we pull a unit.
We serve restaurants and shops along the Memorial Drive corridor and near South DeKalb Mall. Early-morning calls keep service running without interrupting the lunch rush.
Belvedere Park has its own pattern of fridge failures. The housing stock is older, the summers are humid, and the water is hard enough to scale valves. Add power surges from summer storms and you get four problems we see over and over on this route. If you need appliance repair Belvedere Park GA, odds are it is one of these.
Atlanta humidity plus a fridge that gets opened often means the defrost heater and drain line work hard. A partially clogged drain ices over, the defrost cycle stops working, and ice builds on the evaporator until airflow is blocked. We test the defrost heater, defrost thermostat, and timer or board, then clear and flush the drain line. We check the drain pan for cracks and confirm the unit drains correctly. We also verify the defrost cycle completes before we leave.
Many Belvedere Park homes have fridges that are 12 to 18 years old. Compressors wear out, and dirty condenser coils make them run hotter and fail sooner. A failing start relay can also mimic a dead compressor, which is why testing matters. We test the compressor windings and the start relay with a multimeter before recommending a replacement. If the compressor is gone, we recover refrigerant with a recovery machine, swap the compressor, pull a vacuum, and recharge. We also clean the condenser coils.
Summer storms across DeKalb County bring surges that take out control boards, thermostats, and relays. Newer Samsung, LG, and Bosch units are especially sensitive. The symptoms look like a compressor failure, so a guess can cost you hundreds. We test board inputs and outputs with a multimeter and confirm the board is the fault before replacing it. We check the thermostat and relay at the same time. After replacement we recalibrate the temperature control and verify the unit cycles.
Heat and humidity harden door gaskets over time, and a heavy door on a worn hinge sags until the seal no longer touches. The fridge then runs constantly to hold temperature, which wears the compressor and raises the power bill. We test the gasket with a flashlight and a dollar-bill test, then replace it and adjust the hinge. We recheck the seal after alignment. If the door is sagging, we fix the hinge first so the new gasket actually seals.
Watch for these five warning signs before a small fridge problem turns into a compressor replacement.
This is almost always an airflow problem, not a compressor. The evaporator fan motor or a defrost failure is blocking cold air from reaching the fridge side. It is urgent because the freezer will eventually warm up too, and a cheap fan repair can turn into a compressor job if you wait.
A buzzing compressor that is hot to the touch is a failing start relay or a compressor on its way out. A grinding sound is usually a fan motor with a bad bearing. Both get worse, and both are cheaper to fix early. Turn the unit off and call if the noise is loud.
A puddle usually means a clogged defrost drain, a cracked drain pan, or a leaking water line. On older Belvedere Park floors, that water can warp baseboards and subfloor before you notice. Find the source before it becomes a flooring repair.
Check the water line and the inlet valve first. In this part of DeKalb County, hard water scales the valve and freezes the fill tube. A frozen fill tube is a quick fix; a failed valve is a same-visit part swap. Either way, it will not fix itself.
A fridge that never cycles is losing cold air somewhere. The usual suspects are a hardened door gasket, a misaligned door hinge, or dirty condenser coils. It is not an emergency, but it is burning electricity every hour and wearing out the compressor faster.
When you call for Refrigerator Repair near Belvedere Park, we ask three questions on the phone: what the fridge is doing, how old it is, and whether the freezer is still cold. That tells us what to load on the truck. On arrival we test the unit with a multimeter, check airflow, and inspect the door gasket before we touch the sealed system. If refrigerant is involved, we use a manifold gauge set, a leak detector, and a vacuum pump, and we recover old refrigerant with a recovery machine. Belvedere Park homes are a mix of ranch and two-story layouts, so access varies: some kitchens open straight to the driveway, others need the fridge pulled through a narrow galley. We protect floors, measure the cabinet opening, and set the unit back level. If you need emergency appliance repair Belvedere Park GA after hours, we run 24/7 calls and can usually reach 30032 within the hour. Most standard repairs finish in two to four hours.
Fridges in 1950s and 1960s Belvedere Park ranches often sit in a cabinet run that was built for a smaller unit. Pulling a modern 36-inch fridge out for service can scuff floors or jam against a counter if you do not measure first. We measure the opening and the door swing before we move anything. We lay floor protection, pull the unit straight out, and work from the side rather than dragging it. If the clearance is too tight, we service what we can in place and explain what needs to come out.
Atlanta summers push moisture into every fridge that gets opened often. Defrost heaters and drain lines work harder, and a partially clogged defrost drain will ice over and back up into the fridge or onto the floor. We test the defrost heater and thermostat, then clear and flush the drain line. We check the drain pan for cracks and confirm the unit drains to the pan, not the floor. In humid months we recommend a yearly defrost and drain check.
DeKalb County gets strong afternoon storms from June through September. A surge can take out a control board, a thermostat, or a compressor start relay, and the symptoms look similar, so guessing gets expensive. We test the board inputs and outputs with a multimeter before replacing anything. We check the start relay and the thermostat, then confirm the compressor is not the real fault. If a board failed, we replace it and verify the unit cycles correctly.
Water in this part of DeKalb County carries enough mineral content to scale up ice maker inlet valves and water line tubing. A scaled valve drips, freezes, and eventually stops making ice or floods the freezer floor. We pull the valve, inspect the screen and the tubing, and replace the valve and any brittle line. We flush the new line, check every joint under pressure, and confirm the ice maker completes a full cycle before we leave.
Any work that opens the sealed system, recovers refrigerant, or recharges a unit must be done by an EPA Section 608 certified technician. That covers compressor swaps, leak repairs, and gas leak repair. It also means old refrigerant gets recovered with a recovery machine instead of vented.
Sealed system repair in Georgia falls under state licensing for HVAC and refrigeration work. A technician working on your compressor or refrigerant circuit should be able to show that credential. It protects you from a repair that fails a month later with no recourse.
OSHA compliance covers ladder use, electrical lockout, and refrigerant handling on every job. On commercial calls along the Memorial Drive corridor, it also covers safe access to rooftop condensers and walk-in units. It is not paperwork; it is how the job stays safe.
Belvedere Park is easy to work once you know the landmarks. We use Belvedere Park itself and Midway Park as orientation points when routing calls, and Memorial Drive and Columbia Drive as the two main spines. South DeKalb Mall is a useful marker for the commercial side of the route. If you are giving us directions, a landmark plus a cross street gets us there faster than a street address alone.
The park is a central orientation point for the neighborhood that shares its name. We use it to route calls on the surrounding residential streets and to give customers a simple landmark when they are describing where they live.
Midway Park anchors the Midway Road neighborhood and helps us separate that area from the Columbia Drive side. It is a useful reference for scheduling because it sits between two of our most common call clusters.
Memorial Drive is the main commercial spine through Belvedere Park. We use it as the primary route for both residential and commercial calls, and it is the fastest way to move between the east and west sides of the neighborhood.
Columbia Drive runs through the residential heart of the area and connects to several of the streets we serve most. It is our default route when Memorial Drive is backed up, and it puts us close to most ranch-home calls.
South DeKalb Mall is a recognizable marker on the commercial side of Belvedere Park. We use it to orient commercial refrigerator calls along the surrounding retail and food-service corridors.
The Memorial Drive corridor carries a mix of restaurants, small grocery, and service businesses, many with reach-in or walk-in refrigeration. It is the busiest commercial stretch in the Belvedere Park area and the one we route most often for early-morning service calls.
The area around South DeKalb Mall includes retail and food-service tenants with commercial refrigeration needs. We treat these as priority calls because a down unit affects inventory and service, not just comfort.
I-285 sits close to Belvedere Park and gives us a fast route in from the Decatur base and out to surrounding service areas. It is our fallback when surface streets are congested.
We run Refrigerator Repair Belvedere Park calls across the whole 30032 footprint, from the Memorial Drive corridor to the South Decatur side. Below are the areas we hit most often and what makes each one different for fridge work.
A 14-year-old Whirlpool side-by-side in a Memorial Drive corridor ranch stopped cooling on the fridge side while the freezer stayed cold.
We tested airflow first and found the evaporator fan motor seized. The blade was jammed with ice from a partially clogged defrost drain. We replaced the fan motor, cleared and flushed the drain line, and tested the defrost cycle. Total on-site time was about two and a half hours. Fridge side returned to 37 degrees within four hours of the repair. The customer avoided a compressor replacement and the unit is still running today.
A Sub-Zero built-in in a two-story Columbia Drive area home was running constantly and sweating on the door frame.
We checked the door gasket with a flashlight and dollar-bill test and found a hardened seal along the hinge side. The hinge was also slightly out of alignment. We replaced the door gasket, adjusted the hinge, and rechecked the seal. We also cleaned the condenser coils with a coil brush and fin comb. The unit stopped short-cycling and the door frame sweat cleared. Run time dropped noticeably, and the customer reported a lower power bill the following month.
A commercial reach-in at a Memorial Drive corridor food business was warm at 6 a.m. with product inside.
We treated it as a priority call and arrived before service. The compressor start relay had failed, not the compressor itself. We replaced the relay, tested the compressor windings with a multimeter, and confirmed the unit pulled down to temperature. We also checked the condenser for dust and cleaned it. The unit was back to holding temperature before the lunch rush, and no product was lost. The owner added the unit to a preventive maintenance schedule.
4.9
Spring is when pollen and dust hit the condenser coils. Coils clogged with pollen make the compressor run hotter, and the first warm weeks expose a fridge that was already struggling. We see a rise in overheating and not-cooling calls in April and May. Pull the fridge out and vacuum the condenser coils, or book a tune-up. Check the door gasket with a flashlight while you are back there. Clean coils now prevent a summer compressor call.
Summer is our busiest season. High heat and humidity push defrost systems and compressors to their limit, and afternoon storms cause power surges that take out control boards. Ice maker calls also spike because hard water and heat stress the inlet valves. Keep the fridge set at 37 degrees and the freezer at 0, and do not overpack it. If you lose power, wait 10 minutes before plugging the fridge back in. Book any odd noise or warm spot before July.
Fall is the best time to catch problems before the holidays. We see door gasket and hinge issues surface as the weather changes, and we get a lot of requests to service second fridges before holiday cooking. It is also a good window for preventive maintenance. Schedule a tune-up before Thanksgiving. Check the gasket seal and clear the defrost drain. If your fridge is 10 years or older, a fall check is cheaper than a holiday emergency call.
Winter is quieter for cooling calls but harder on garage and basement fridges. Cold ambient temperatures can fool the thermostat and cause the unit to stop cycling correctly. We also see compressor start issues on very cold mornings in unheated spaces. If your second fridge is in the garage, check that it is rated for that space. Keep the door seal clean and dry. If the unit short-cycles in cold weather, call before it fails completely.
Not every fridge repair call in Belvedere Park is the same, and not every technician is either. These five questions separate a real diagnostic technician from someone who swaps parts until the fridge works. Ask them before you book, and you will avoid the second call.
A failing start relay or control board can look exactly like a dead compressor. If a technician jumps straight to a compressor quote without testing windings, relay, and pressures, you may be paying for a part you did not need. Testing first is the difference between a $200 repair and a $900 one.
Any repair that opens the sealed system requires EPA Section 608 certification. It also means old refrigerant gets recovered properly instead of vented. If the answer is vague, the technician should not be touching your compressor or refrigerant circuit.
Fan motors, thermostats, defrost heaters, and relays are common failures we stock. If a technician has to order every part, your fridge sits warm for days. Ask what is on the truck and what the expected turnaround is for anything that needs ordering.
A diagnostic fee is normal, but it should be disclosed upfront and credited if you approve the work. If the fee is high and not credited, you are paying twice. Get the number before the visit, not after.
On a 15-year-old fridge, a compressor replacement can cost more than the unit is worth. A straight technician will say so and help you decide. One who never recommends replacement is selling you a repair, not solving your problem.
Most standard repairs in Belvedere Park run $180 to $450 in 2026, with the diagnostic visit credited toward the work if you approve it. Fan motors, thermostats, and defrost heaters sit at the lower end. Control boards and compressor replacements push higher, and sealed system work costs more because it requires recovery, a vacuum pull, and a recharge. We quote the number before we start.
The best Refrigerator Repair in Belvedere Park GA is the one that tests before it quotes. Ask whether the technician uses a multimeter and manifold gauge set, whether they are EPA Section 608 certified, and whether they will tell you when a repair is not worth it. We work the 30032 route weekly and stand behind our diagnosis. Check the reviews from your own neighborhood.
Yes. We run 24/7 emergency appliance repair Belvedere Park GA calls for fridges that have stopped cooling with food at risk. Call and tell us the fridge is down and whether the freezer is still cold. We prioritize those calls and can usually reach 30032 within the hour. Commercial units holding product get the same priority.
Yes, same-day fridge repair in Belvedere Park GA is available seven days a week, and most calls in 30032 get a same-day window. We stock common parts like fan motors, thermostats, defrost heaters, and relays on the truck, so many repairs finish in one visit. Call before noon for the best chance at a same-day slot.
We repair Samsung, LG, Whirlpool, GE, Frigidaire, Maytag, KitchenAid, Sub-Zero, Bosch, and Kenmore in Belvedere Park. That covers most of what is in the ranch and two-story homes here, plus the built-in Sub-Zero and Bosch units that need careful panel removal. If your model is not listed, call and we will tell you straight.
If your fridge is warm and you have food at risk, call us now. We run Refrigerator Repair in Belvedere Park seven days a week, with 24/7 emergency calls across 30032 and the Memorial Drive corridor. We test before we quote, we carry common parts on the truck, and we tell you when a repair is not worth it. One call gets a technician on the way.
Call +14702044981 and tell us the brand, model and what your fridge is doing. We book real windows, usually same-day, and text you when the tech is on the way. If you prefer email, send the details to info@refrigeratorrepairexperts.com and we will reply with a time.
