Written scope
What we will do before we start
Refrigerator Installation Decatur GA done right the first time
Refrigerator Installation Decatur GA means more than sliding a box into a cabinet slot. We disconnect the old unit, protect your floors, set the new fridge level, run and test the water line, and haul the old one away. Whether you bought a Samsung French-door or a Sub-Zero built-in, we handle the heavy lifting and the details so your kitchen is cold and running the same day.
- New fridge install
- Water line hookup
- Old fridge haul away
- Readings on every visitTemperatures written down before and after
- Old part handed overYou see what failed
- Floor protected firstMats down before the fridge moves
- Test run before leavingFridge cycles and holds temperature
What our Refrigerator Installation includes
Every standard install includes the items below. If we find something that needs extra work, like a corroded shutoff valve or a cabinet opening that is too small, we quote it before we start. You approve the number before we touch anything.
- Disconnect and removal of old unitWe unplug the old refrigerator, shut off the water supply, and disconnect the line. If the old unit has a copper line with a saddle valve, we replace it with a proper shutoff. We move the old fridge out of the way and protect the floor along the route.
- Set, level, and align new fridgeWe bring the new refrigerator in, remove the doors if needed, and set it in the opening. Then we adjust the leveling legs so the unit sits flat and the doors self-close. We check clearance at the back for the condenser coil and confirm the door gasket seals all the way around.
- Water line hookup and leak testWe run new water line tubing from the shutoff to the fridge inlet, install a fresh compression fitting, and open the valve. Then we run two ice maker cycles and check every connection with a leak detector. If your model has a water filter, we install it and flush two gallons through the dispenser.
- Temperature and door seal checkWe let the compressor run for 30 minutes, check the temperature in both compartments with a thermometer, and confirm the doors seal. We also check the door gasket with a dollar-bill test to make sure there are no gaps.
- Haul away old refrigeratorWe disconnect the old unit, cap the water line, and load it on the truck. No curbside pile, no waiting for a bulk pickup. For Decatur customers in 30030 and 30031, we can usually haul the old fridge the same day we install the new one.
- Walkthrough and settings reviewWe show you how to set the temperature, reset the water filter indicator, and adjust the shelves. We also leave you with a card that has our number in case you have questions in the first 90 days.
Refrigerator installation for homes
We install refrigerators in houses, condos, and apartments across Decatur. We measure the path, remove doors if needed, and test the water line before we leave.
- Tight hallway and doorway fits
- Copper line and saddle valve replacement
- Built-in and counter-depth alignment
- Old refrigerator hauled away same day
Refrigerator installation for businesses
We install refrigerators in rental units, offices, and commercial kitchens across Decatur. We coordinate with property managers and schedule around your tenants.
- Rental unitsInstall between tenants with same-day haul away
- OfficesInstall breakroom refrigerators with water line hookup
- Commercial kitchensInstall reach-in and prep table refrigerators
- Property managersSchedule multiple unit installs in one visit
What Refrigerator Installation Decatur GA actually involves
Refrigerator Installation Decatur GA is the full job of removing an old unit, prepping the space, and commissioning a new refrigerator so it cools, freezes, and makes ice without leaks or vibration. That means checking the water line tubing and shutoff valve, verifying the door gasket seals, leveling the cabinet so the doors close on their own, and letting the compressor settle before you load it with groceries. We bring a multimeter, tube cutter, flaring tool, and a leak detector to every call.
Most Decatur homes were built before 1970, and the kitchen cabinet openings were sized for 30-inch fridges that no longer exist. A new 36-inch French-door may not fit without adjusting trim or moving a water line. We measure the opening, the door swing, and the hallway path before we lift anything. If you searched for Refrigerator Installation near me Decatur GA, this is the kind of prep that separates a clean install from a scratched floor and a kinked line.
We set, level, connect, and test every refrigerator before we leave your kitchen.
How our fridge install in Decatur GA works
Every install follows the same five steps. Most jobs take two to four hours from arrival to final test, depending on whether we need to modify cabinets or run a new water line.
Measure and prep
We measure the cabinet opening, the door swing, and the path from your front door to the kitchen. We check the existing water shutoff valve and the outlet. If the opening is too tight for the new unit, we tell you before we unbox anything. This step takes about 20 minutes.
Disconnect the old unit
We unplug the old refrigerator, shut off the water supply, and disconnect the line. If the old unit has a copper line with a saddle valve, we replace it with a proper shutoff. We move the old fridge out of the way and protect the floor along the route.
Set and level the new fridge
We bring the new refrigerator in, remove the doors if needed, and set it in the opening. Then we adjust the leveling legs so the unit sits flat and the doors self-close. We check clearance at the back for the condenser coil and confirm the door gasket seals all the way around.
Connect and test the water line
We run new water line tubing from the shutoff to the fridge inlet, install a fresh compression fitting, and open the valve. Then we run two ice maker cycles and check every connection with a leak detector. If your model has a water filter, we install it and flush two gallons through the dispenser.
Final test and haul away
We let the compressor run for 30 minutes, check the temperature in both compartments with a thermometer, and confirm the doors seal. Then we load the old fridge on the truck and sweep up. You get a walkthrough of the settings and the water filter reset procedure before we leave.
Tools and methods we use for refrigerator installation
Multimeter
We test the outlet voltage and check the refrigerator's electrical components before and after install to confirm everything is getting proper power.
Tube cutter and flaring tool
We cut fresh water line tubing to length and create a clean flare or compression fitting. This prevents leaks at the connection point.
Leak detector
We check every water line connection and the ice maker inlet for drips. We run two ice maker cycles while we are still on site.
Manifold gauge set
If we need to check refrigerant pressure on a sealed system, we use a manifold gauge set. This is required for any compressor or refrigerant work.
Vacuum pump and refrigerant recovery machine
If the install involves a sealed system repair, we use a vacuum pump to evacuate the lines and a recovery machine to handle refrigerant safely.
Fin comb and coil brush
We clean the condenser coil before we set the fridge in place. A clean coil helps the compressor run efficiently from day one.
Furniture dolly and floor protection
We use a 500-pound-rated dolly and lay down floor protection to move the refrigerator through your home without scratching floors or doorways.
Measure twice, lift once
We measure the cabinet opening, the door swing, and the path from your front door to the kitchen before we unbox anything. If the opening is too tight for the new unit, we tell you before we lift it. This step takes about 20 minutes and prevents damage.
When Decatur customers call us for refrigerator installation
You bought a new refrigerator from a big-box store and the delivery crew will not hook up the water line or haul away the old unit.
We handle the full install: disconnect the old unit, set and level the new one, run and test the water line, and haul the old fridge away. We do this in one visit, usually in two to four hours. You have a cold, level refrigerator with a working ice maker and no old appliance sitting in your kitchen.
You are remodeling your kitchen in Druid Hills and need the new built-in refrigerator installed after the cabinets are set.
We install built-in refrigerators like Sub-Zero and KitchenAid. We align the panels, set the trim, and run a 90-degree water line elbow if needed. We coordinate with your contractor on timing. Your built-in fridge sits flush with the cabinets, the doors close properly, and the ice maker works.
Your old fridge died on a Friday night and you need a new one installed before the weekend groceries spoil.
We hold open slots every weekday for same-day fridge install in Decatur, Georgia. Call before noon and we can usually be there by late afternoon. We install, test, and haul away the old unit. You have a running refrigerator the same day, and your groceries stay cold.
You are a landlord in Decatur Heights and need a refrigerator installed in a rental unit between tenants.
We install refrigerators in rental units across Decatur. We coordinate with your property manager, install the unit, test the water line, and haul away the old fridge. We leave the unit clean and ready for the next tenant. The rental unit is ready to show, and you do not have to manage the install yourself.
How refrigerator installation runs in Decatur
Decatur's housing stock is old. Most homes in Oakhurst, Winnona Park, and Decatur Heights were built between 1920 and 1960, and the kitchen cabinet openings were sized for 30-inch refrigerators that are no longer made. A new 36-inch French-door unit often will not fit without adjusting trim or moving a water line. We measure the opening, the door swing, and the hallway path before we lift anything. If you searched for Refrigerator Installation near me Decatur GA, this is the kind of prep that separates a clean install from a scratched floor and a kinked line. We also deal with older plumbing. Many Decatur homes still have copper water lines with saddle valves that leak when you touch them. We replace those with proper shutoff valves during the install. If you need emergency Refrigerator Installation Decatur GA on a weekend, call us and we will tell you honestly whether we can get there the same day.
- OakhurstMostly 1920s bungalows with narrow hallways and original hardwood floors. We remove refrigerator doors to fit units through tight spaces and use floor protection.
- Decatur HeightsMix of older homes and new construction. We see a lot of counter-depth refrigerators that need precise leveling and water line adjustments.
- Druid HillsLarger homes with built-in refrigerators and custom cabinetry. We align panels and trim to match the cabinet finish.
- Downtown DecaturCondos and lofts with tight kitchen layouts. We measure the elevator and hallway path before we schedule the install.
- Older homes with copper water lines and saddle valvesSaddle valves often leak when you disconnect the old fridge. We replace them with proper shutoff valves during the install so you do not have a drip under the new unit.
- Kitchen cabinet openings sized for 30-inch refrigeratorsA new 36-inch French-door unit may not fit without trimming the cabinet or moving the water line. We measure first and tell you what needs to change.
From problem to finished result.
From dead fridge to cold groceries in Oakhurst
BeforeA 15-year-old Whirlpool refrigerator stopped cooling on a Friday. The homeowner had a new Samsung French-door unit sitting in the living room because the delivery crew would not remove the doors to fit it through the hallway.
AfterWe removed the refrigerator doors, moved the new unit into the kitchen, reattached the doors, leveled it, and hooked up the water line. The ice maker was working within three hours. The old fridge was hauled away the same day.
We showed the homeowner how to clean the condenser coil every six months and check the door gasket with a dollar-bill test. That keeps the compressor from working overtime.
Built-in Sub-Zero install in Druid Hills
BeforeA homeowner was remodeling their kitchen and needed a new Sub-Zero built-in refrigerator installed after the cabinets were set. The cabinet opening was 1/4 inch too narrow, and the water line was on the wrong side.
AfterWe trimmed the cabinet opening, rerouted the water line with a 90-degree elbow, and aligned the Sub-Zero panels flush with the cabinets. The doors self-close, and the ice maker was tested twice before we left.
We recommended a annual coil cleaning and a door gasket check. Built-in units need panel alignment checked once a year to keep the doors closing properly.
Same-day rental unit install in Decatur Heights
BeforeA property manager had a tenant moving in on Saturday and the refrigerator in the unit was not cooling. The old unit was a 20-year-old GE that had a compressor failure.
AfterWe installed a new Whirlpool refrigerator on Friday afternoon, hooked up the water line, tested the ice maker, and hauled away the old GE. The tenant moved in Saturday morning with a working fridge.
We left a card with our number and recommended a preventive maintenance plan that includes annual coil cleaning and temperature checks.
Problems we solve with new refrigerator installation in Decatur
A new refrigerator that is not installed correctly can leak, vibrate, or fail to cool. Here are the most common problems we fix for Decatur customers.
New fridge will not fit through the hallway or cabinet opening
We measure the path and the opening before we lift anything. If the fridge doors need to come off, we remove them and reinstall them. If the cabinet opening is too tight, we trim the trim or adjust the water line. We have fit 36-inch French-door units through 28-inch doorways in Winnona Park bungalows. You are stuck with a fridge in your living room and a delivery crew that will not remove doors or trim cabinets.
Water line leaks after install
We cut fresh water line tubing, install a new compression fitting, and test every connection with a leak detector. We run two ice maker cycles while we are still on site. If it drips, we fix it before we pack up. A slow drip under the fridge can warp hardwood floors and grow mold in the subfloor within a week.
Fridge rocks or doors swing open on their own
We adjust the leveling legs and check the door gasket contact with a dollar-bill test. We confirm the doors self-close. That keeps the compressor from working overtime and your energy bill from creeping up. An unleveled fridge makes the compressor work harder, which shortens its life and raises your energy bill.
Old fridge is still sitting in the kitchen after new one arrives
We disconnect the old unit, cap the water line, and load it on the truck. No curbside pile, no waiting for a bulk pickup. For Decatur customers in 30030 and 30031, we can usually haul the old fridge the same day we install the new one. You have two refrigerators, no floor space, and no way to move a 300-pound appliance by yourself.
A level, leak-free refrigerator that cools and makes ice from day one.
No floor or door damage
We lay down floor protection, remove the refrigerator doors when the hallway is tight, and use a furniture dolly rated for 500 pounds. In older Decatur homes with original hardwood, that matters. We have moved units through 28-inch doorways in Winnona Park bungalows without a single scratch.
Water line tested before we leave
A kinked or cross-threaded water line tubing is the number one cause of a puddle under a new fridge. We cut fresh tubing, install a new compression fitting, and run two full cycles through the ice maker while we are still on site. If it drips, we fix it before we pack up.
Leveled and aligned doors
A refrigerator that rocks or has a door that swings open on its own is not installed correctly. We adjust the leveling legs, check the door gasket contact with a dollar-bill test, and confirm the doors self-close. That keeps the compressor from working overtime and your energy bill from creeping up.
Old fridge hauled away same day
We disconnect the old unit, cap the water line, and load it on the truck. No curbside pile, no waiting for a bulk pickup. For Decatur customers in 30030 and 30031, we can usually haul the old fridge the same day we install the new one.
What you receive
Clear records you can keep and share.
Flat-rate quote
The full price before we touch anything
Install checklist
What we tested and confirmed before we left
What to know before your refrigerator install
A refrigerator needs a level surface, a clean water connection, and a few hours to settle. Here is what matters most before we arrive.
Measure the opening
Measure your cabinet opening, the door swing, and the path from your front door to the kitchen. A new 36-inch unit may not fit a 30-inch opening without adjustments.
Check the water shutoff
Find the water shutoff valve behind or under the fridge. If it is a saddle valve on copper pipe, it may leak when disconnected. We replace those during the install.
Let the compressor settle
After the refrigerator is moved into place, let it sit for 30 minutes before plugging it in. This lets the compressor oil settle and prevents damage.
Refrigerator repair coverage around Decatur
- Downtown Decatur
- Old Decatur
- Decatur Heights
- Oakhurst
- Winnona Park
- Clairemont-Great Lakes
- Midway Woods
- Lenox Place
- Glennwood Estates
- Ponce de Leon Heights
- Westchester Hills
- Chelsea Heights
- Druid Hills
- North Decatur
Outside these areas? Call and ask, we may still cover you +14702044981
What Decatur customers say
Standard refrigerator installation in Decatur runs $149 to $249 in 2026. That covers disconnect, set, level, water line hookup, and haul away. Built-in or counter-depth units run $299 to $450 because they need panel alignment and tighter clearances. If we need to run a new water line or replace a shutoff valve, that adds $75 to $150. We quote the full number before we start.
We do. Our technicians install refrigerators across Decatur and DeKalb County every weekday. We are not a retail delivery crew. We are appliance techs who carry a multimeter, tube cutter, flaring tool, and leak detector on every call. Call +14702044981 and we can usually schedule a same-day or next-day slot.
Yes. Standard installation includes haul away of your old refrigerator at no extra charge. We disconnect it, cap the water line, and load it on the truck. We do not leave it on the curb. If your old unit is a built-in that needs to be dismantled to remove, we quote that separately before we start.
Yes. We install Sub-Zero, KitchenAid, Bosch, and other built-in refrigerators regularly. Built-ins need panel alignment, custom trim, and sometimes a 90-degree water line elbow. We bring shims, a level, and the right fittings. Expect the job to take three to five hours. We test the ice maker and check the door gasket before we leave.
Schedule your Refrigerator Installation Decatur GA today
We have same-day and next-day slots available this week. Call +14702044981 and we will confirm your appointment, give you a flat-rate quote, and tell you exactly what to expect. No deposit required.
Contact Our Decatur Team
Call +14702044981 and tell us the brand, model and what your fridge is doing. We book real windows, usually same-day, and text you when the tech is on the way. If you prefer email, send the details to info@refrigeratorrepairexperts.com and we will reply with a time.